Welding electrodes Vistek the SSSI 13/55 f 4 mm 5 kg
Offer type: salePublished: 12.10.2015
| Price: | negotiated |
| Seller: |  Mihail |
| Phones: |  0973666601 Show phone 0660770602 Show phone |
| Address: | Ukraine, Kharkivs'ka Oblast' |
When
buying this product through the website
http://svarmetall.com.ua/p27884262-svarochnye-elektrody-vistek.html
there is a cumulative system of discounts. Also, for some products site apply FREE shipping to any settlement of Ukraine.
There is a wide range of the wire:
http://svarmetall.com.ua/g3490980-svarochnye-elektrody
Type AA
The electrodes of the UEZ SSSI 13/55, designed for manual arc welding heavy duty constructions from carbon and low alloy steels, when the metal welds are increased requirements for plasticity and impact toughness, especially at low temperatures.
Welding in all spatial positions, except vertical top down, the constant power source circuit voltage (50±5) V and AC circuit voltage of the power source (70±10) V. The permissible moisture content in the coating prior to use is not more than 0.3 %. A repeat calcination: drying at 400°C for 1 hour. Approved NAKS the following groups of technical devices: long, TH, KO, MOE, OGC, OTOH, KNIT, TVE PR.
Recommended current (A)
Diameter, mm current
The 3.0 - 80-130
4,0 - 150-170
A 5.0 180-210
Specifications
The main characteristics of the weld metal and deposited metal
Mechanical properties of seam metal, not less than
• Tensile strength, MPa: 490
• Elongation, %: 20
• Impact strength, j/cm2: 127
Chemical composition of deposited metal, %
• Carbon: 0,08-0,12
• Manganese: 0,8-1,0
• Silicon: 0.18 to 0.40 to
• Sulfur: 0,03
• Phosphorus: 0,3
http://svarmetall.com.ua/p27884262-svarochnye-elektrody-vistek.html
there is a cumulative system of discounts. Also, for some products site apply FREE shipping to any settlement of Ukraine.
There is a wide range of the wire:
http://svarmetall.com.ua/g3490980-svarochnye-elektrody
Type AA
The electrodes of the UEZ SSSI 13/55, designed for manual arc welding heavy duty constructions from carbon and low alloy steels, when the metal welds are increased requirements for plasticity and impact toughness, especially at low temperatures.
Welding in all spatial positions, except vertical top down, the constant power source circuit voltage (50±5) V and AC circuit voltage of the power source (70±10) V. The permissible moisture content in the coating prior to use is not more than 0.3 %. A repeat calcination: drying at 400°C for 1 hour. Approved NAKS the following groups of technical devices: long, TH, KO, MOE, OGC, OTOH, KNIT, TVE PR.
Recommended current (A)
Diameter, mm current
The 3.0 - 80-130
4,0 - 150-170
A 5.0 180-210
Specifications
The main characteristics of the weld metal and deposited metal
Mechanical properties of seam metal, not less than
• Tensile strength, MPa: 490
• Elongation, %: 20
• Impact strength, j/cm2: 127
Chemical composition of deposited metal, %
• Carbon: 0,08-0,12
• Manganese: 0,8-1,0
• Silicon: 0.18 to 0.40 to
• Sulfur: 0,03
• Phosphorus: 0,3
