Machine for edging VMA-25 (ABM-26)
Offer type: salePublished: 22.08.2014
| Seller: |  Sharapov Aleksej |
| Phones: |  (8452)760-850 Show phone760-860 Show phone |
| Address: | Russian Federation, Saratovskaya Oblast', Saratov |
Pastores VMA-25 (ABM-26) carries out cutting edge before welding, with automatic feed. Edger is designed to handle the edges of the steel and aluminium sheets before welding in automatic mode and allows you to capture chamfer up to 25 mm in the range from 0 to 60 degrees.
Automatic feeding significantly increases productivity. By the alignment of the segments and clamping-clamps included in the kit pastoriza, edger VMA-25 (ABM-26) is mounted on the treated sheet for two minutes. The shooting speed bevel is relatively high and is about 350-500 mm / minute at an angle of 45 degrees.
Machine for shooting chamfer VMA-25 the most effective use of plants that require long processing steel sheets.
Pastores VMA-25 has an electric drive powered by 220 volts. For the comfort operating working edger is equipped with an electronic protection in case of sudden emergencies caused by violation of safety regulations and special electronic control device edge of the steel sheet.
Factorise as a working tool using a special cutter, which has 7 (seven) carbide inserts that allow you to delete the desired metal, without changing its structure. Basically, it is possible to capture the whole width of the chamfer cut at one time. Pre-treat the edge of the surface before work pastoriza after cutting gas is not necessary.
Pastores VMA-25 (ABM-26) is well established in enterprises which produce bridge structures, ship hulls and build oil terminal. This edger allows you to capture chamfer length of 10-15 meters, it is necessary to order additional guides segments. Shooting chamfer is very high quality, it is always the specialists!
The delivery set includes:
aggregate VMA-25
- guides
- clamping device for directing
- set carbide inserts
set - top box for angles of 0, 15, 30, 45 degrees
YOU order the machine to capture chamfers VMA-25 (ABM-26) completed with additional tracks.
To calculate the necessary number of additional segments can YOU yourself, length 1 piece -1200 mm
Automatic feeding significantly increases productivity. By the alignment of the segments and clamping-clamps included in the kit pastoriza, edger VMA-25 (ABM-26) is mounted on the treated sheet for two minutes. The shooting speed bevel is relatively high and is about 350-500 mm / minute at an angle of 45 degrees.
Machine for shooting chamfer VMA-25 the most effective use of plants that require long processing steel sheets.
Pastores VMA-25 has an electric drive powered by 220 volts. For the comfort operating working edger is equipped with an electronic protection in case of sudden emergencies caused by violation of safety regulations and special electronic control device edge of the steel sheet.
Factorise as a working tool using a special cutter, which has 7 (seven) carbide inserts that allow you to delete the desired metal, without changing its structure. Basically, it is possible to capture the whole width of the chamfer cut at one time. Pre-treat the edge of the surface before work pastoriza after cutting gas is not necessary.
Pastores VMA-25 (ABM-26) is well established in enterprises which produce bridge structures, ship hulls and build oil terminal. This edger allows you to capture chamfer length of 10-15 meters, it is necessary to order additional guides segments. Shooting chamfer is very high quality, it is always the specialists!
The delivery set includes:
aggregate VMA-25
- guides
- clamping device for directing
- set carbide inserts
set - top box for angles of 0, 15, 30, 45 degrees
YOU order the machine to capture chamfers VMA-25 (ABM-26) completed with additional tracks.
To calculate the necessary number of additional segments can YOU yourself, length 1 piece -1200 mm
