Resistance spot welding DC MTR-19053
Offer type: salePublished: 20.05.2018
| Seller: |  Evgenij Efimovich |
| Phones: |  8-4912-777-932 Show phone |
| Address: | Russian Federation, Ryazanskaya Oblast', Ryazan' |
Machine resistance spot welding DC MTR-19053 high-speed compact machine for intensive work on a variety of productions, with reduced requirements for operating conditions.
The machine is designed for welding with direct current sheet materials from mild steel, stainless and galvanized steel, aluminum and titanium alloys, copper, brass, and construction reinforcement and masonry grid.
The car is certified, the most important sites are protected by patents of the Russian Federation.
MTWR-19053 is microprocessor controlled modes of operation with digital display, an electromagnetic actuator and integrated closed-loop liquid cooling system of electrodes. Supply hoses to the electrodes is also hidden. Given the differences make the machine offline, requiring only network 380.
The machines are manufactured with the departure of the electrodes from 350 mm to 1000 mm are Possible staffing feeder that allows you to extend the capabilities of welding.
Machine resistance spot welding DC MTR-19053:
- does not require pneumatic
- does not require water supply and sanitation
- has a maximum short circuit current of 22 kA
- has a maximum welding current at a basic flight 19 kA
- has high efficiency, up to 90 welds per minute
- basic departure electrodes 600 mm (from 350 to 1000 mm)
- design of trunk and electrodes can perform a wide range of work, including welding the parts of various configurations and cross-sections
Operating conditions of the machine MTWR-19053
- ambient temperature from - 10 to + 40 °C
- relative humidity up to 90% at 25 °C
- atmospheric pressure of from 60 to 104 kPa (450 to 780 mm RT. Art.)
Parametrization
Voltage pitaniya/220
Power consumption, mokwa
Most secondary tocca
Most welding current kA
Weldable thickness of sheet materials
- low carbon stalma 6 + 6
- galvanized stalma 3 + 3
- stainless stalma 3,5 + 3,5
- cadmium-plated stalma 3 + 3
- titanium splaymidi 3 + 3
- aluminum splaymidi 3 + 3
- mediumto 2 + 2
- latunde 2 + 2
Welded diameters fittings
class A1, Vmdo 16 + 16
class A2, Vmdo 14 + 14
- galvanized fittings, mmda 10 + 10
Gabaritima
Massakh
Fundamental differences from similar machines resistance spot welding:
1. Autonomous built-in liquid cooling system
2. Electromagnetic actuator
3. Hidden cooled electrodes
4. Special design of trunk and electrodes
5. Microcontroller regulator welding
Is a self-contained liquid cooling system eliminates the need to provide water supply and Sewerage. In addition, this system is integrated in the housing of the machine, which reduces its dimensions.
An electromagnetic drive eliminates the need to bring the compressed air, which gives advantages over pneumatic actuator. This is especially important where there is no airset, because otherwise you would have to buy another compressor. At the same time, the electromagnetic actuator provides performance of up to 90 welds per minute and allows you to perform a large amount of work that gives certain advantages over other types of drives. The presence of two pedals allows you to apply the cyclic modes, multipulse, and a single weld.
-Hidden cooled electrodes (without protruding hose), special design of trunk and electrodes, makes it possible to weld the parts close to the electrodes, with a minimum flanging, welding cylinders and boxes, welding wire and rebar, as well as to welding parts located inside drawers, boxes, cylinders, etc.
-Versions with index B allow welding of cylindrical products with a diameter of 80 mm or more, in length from 250 mm to 900 mm
-Microcontroller regulator welding provides quality welding in the following modes:
- automatic continuous welding;
- welding of single pulses;
- edit and aiming (compression without welding and deferred welding);
- multipulse mode welding;
- deferred welding;
- manage multiple machines from one pedal; (for example, when welding the wire mesh in several places).
MTWR-19053 produced, differing in the length of the flight and the design of the electrode holders. Apply only finger electrodes of an alloy of high strength for longer life.
Modified in order to weld the parts of the cylindrical configuration, the suffix B.
- MTWR-19053-35 - departure electrodes 350 mm
- MTWR-19053-45 - departure electrodes 450 mm
- MTWR-19053-50 - departure electrodes 500 mm
- MTWR-19053-60 - departure electrodes 600 mm
- MTWR-19053-70 - departure electrodes 700 mm
- MTWR-19053-90 - departure electrodes 900 mm
- MTWR-19053-10 - flight of the electrodes 1000 mm
Modification index B allow welding of cylindrical products with a diameter of 80 mm or more, in length from 250 mm to 900 mm
- MTWR-19053-35B - weld the cylindrical article length 250 mm
- MTWR-19053-45 - weld the cylindrical article length 350 mm
- MTWR-19053-50B - weld cylindrical products with a length of 400 mm
- MTWR-19053-60B - weld cylindrical products with a length of 500 mm.
- MTWR-19053-B - weld the cylindrical article length 600 mm
- MTWR-19053-B - weld the cylindrical article length 800 mm
- MTWR-19053-10B - weld the cylindrical article length 900 mm
Modification with the departure of the electrodes 900 mm can be welded pipes Ø from 80 mm and length up to 800 mm
Diverse range of welded materials and high performance provide a wide use of the machine in various industries and small businesses. A large flight of the electrodes, no hoses to cool the electrodes for welding alloys of non-ferrous metals, stainless and galvanized steel, allow you to use MTR-19053 in the production of critical parts of complex configuration.
Machine can be used in any room, at low temperatures, in any room, outside under a canopy. Thanks to these features it will be convenient and useful for different types of industries. Dimensions, weight and autonomy of the machine allow, if necessary, easy to move and quick to get to work.
If you buy resistance spot welding, the optimal choice is MTP-19053 and MTVR-19053.
Machine resistance spot welding MTP-19053 and MTVR-19053 only machine radial type, which have a radius of electrodes up to 1000 mm with a relatively low weight and small dimensions.
However, they are capable of welding various thicknesses of materials from 0.3 to+0.3 mm to 6+6 mm, which makes them universal, that is, there is no need to purchase multiple machines of different capacities for welding metals of different thickness.
A characteristic feature of our machines, resistance spot welding is a wide possibility to adjust the magnitude of welding current: connect machines to the voltage as 380 V and 220 V, as well as simple and logical current regulation on the control panel, allows you to vary the modes, choosing in each case the optimum welding current.
Simple and intuitive adjustment of the solution electrodes, the free motion of the electrodes, the compression efforts, make it easy to reconfigure the machine resistance spot welding for solving specific production problems.
Thus, customers who wish to buy cars contact spot welding, can save a lot of money, fully using the potential of our machines.
The machine is designed for welding with direct current sheet materials from mild steel, stainless and galvanized steel, aluminum and titanium alloys, copper, brass, and construction reinforcement and masonry grid.
The car is certified, the most important sites are protected by patents of the Russian Federation.
MTWR-19053 is microprocessor controlled modes of operation with digital display, an electromagnetic actuator and integrated closed-loop liquid cooling system of electrodes. Supply hoses to the electrodes is also hidden. Given the differences make the machine offline, requiring only network 380.
The machines are manufactured with the departure of the electrodes from 350 mm to 1000 mm are Possible staffing feeder that allows you to extend the capabilities of welding.
Machine resistance spot welding DC MTR-19053:
- does not require pneumatic
- does not require water supply and sanitation
- has a maximum short circuit current of 22 kA
- has a maximum welding current at a basic flight 19 kA
- has high efficiency, up to 90 welds per minute
- basic departure electrodes 600 mm (from 350 to 1000 mm)
- design of trunk and electrodes can perform a wide range of work, including welding the parts of various configurations and cross-sections
Operating conditions of the machine MTWR-19053
- ambient temperature from - 10 to + 40 °C
- relative humidity up to 90% at 25 °C
- atmospheric pressure of from 60 to 104 kPa (450 to 780 mm RT. Art.)
Parametrization
Voltage pitaniya/220
Power consumption, mokwa
Most secondary tocca
Most welding current kA
Weldable thickness of sheet materials
- low carbon stalma 6 + 6
- galvanized stalma 3 + 3
- stainless stalma 3,5 + 3,5
- cadmium-plated stalma 3 + 3
- titanium splaymidi 3 + 3
- aluminum splaymidi 3 + 3
- mediumto 2 + 2
- latunde 2 + 2
Welded diameters fittings
class A1, Vmdo 16 + 16
class A2, Vmdo 14 + 14
- galvanized fittings, mmda 10 + 10
Gabaritima
Massakh
Fundamental differences from similar machines resistance spot welding:
1. Autonomous built-in liquid cooling system
2. Electromagnetic actuator
3. Hidden cooled electrodes
4. Special design of trunk and electrodes
5. Microcontroller regulator welding
Is a self-contained liquid cooling system eliminates the need to provide water supply and Sewerage. In addition, this system is integrated in the housing of the machine, which reduces its dimensions.
An electromagnetic drive eliminates the need to bring the compressed air, which gives advantages over pneumatic actuator. This is especially important where there is no airset, because otherwise you would have to buy another compressor. At the same time, the electromagnetic actuator provides performance of up to 90 welds per minute and allows you to perform a large amount of work that gives certain advantages over other types of drives. The presence of two pedals allows you to apply the cyclic modes, multipulse, and a single weld.
-Hidden cooled electrodes (without protruding hose), special design of trunk and electrodes, makes it possible to weld the parts close to the electrodes, with a minimum flanging, welding cylinders and boxes, welding wire and rebar, as well as to welding parts located inside drawers, boxes, cylinders, etc.
-Versions with index B allow welding of cylindrical products with a diameter of 80 mm or more, in length from 250 mm to 900 mm
-Microcontroller regulator welding provides quality welding in the following modes:
- automatic continuous welding;
- welding of single pulses;
- edit and aiming (compression without welding and deferred welding);
- multipulse mode welding;
- deferred welding;
- manage multiple machines from one pedal; (for example, when welding the wire mesh in several places).
MTWR-19053 produced, differing in the length of the flight and the design of the electrode holders. Apply only finger electrodes of an alloy of high strength for longer life.
Modified in order to weld the parts of the cylindrical configuration, the suffix B.
- MTWR-19053-35 - departure electrodes 350 mm
- MTWR-19053-45 - departure electrodes 450 mm
- MTWR-19053-50 - departure electrodes 500 mm
- MTWR-19053-60 - departure electrodes 600 mm
- MTWR-19053-70 - departure electrodes 700 mm
- MTWR-19053-90 - departure electrodes 900 mm
- MTWR-19053-10 - flight of the electrodes 1000 mm
Modification index B allow welding of cylindrical products with a diameter of 80 mm or more, in length from 250 mm to 900 mm
- MTWR-19053-35B - weld the cylindrical article length 250 mm
- MTWR-19053-45 - weld the cylindrical article length 350 mm
- MTWR-19053-50B - weld cylindrical products with a length of 400 mm
- MTWR-19053-60B - weld cylindrical products with a length of 500 mm.
- MTWR-19053-B - weld the cylindrical article length 600 mm
- MTWR-19053-B - weld the cylindrical article length 800 mm
- MTWR-19053-10B - weld the cylindrical article length 900 mm
Modification with the departure of the electrodes 900 mm can be welded pipes Ø from 80 mm and length up to 800 mm
Diverse range of welded materials and high performance provide a wide use of the machine in various industries and small businesses. A large flight of the electrodes, no hoses to cool the electrodes for welding alloys of non-ferrous metals, stainless and galvanized steel, allow you to use MTR-19053 in the production of critical parts of complex configuration.
Machine can be used in any room, at low temperatures, in any room, outside under a canopy. Thanks to these features it will be convenient and useful for different types of industries. Dimensions, weight and autonomy of the machine allow, if necessary, easy to move and quick to get to work.
If you buy resistance spot welding, the optimal choice is MTP-19053 and MTVR-19053.
Machine resistance spot welding MTP-19053 and MTVR-19053 only machine radial type, which have a radius of electrodes up to 1000 mm with a relatively low weight and small dimensions.
However, they are capable of welding various thicknesses of materials from 0.3 to+0.3 mm to 6+6 mm, which makes them universal, that is, there is no need to purchase multiple machines of different capacities for welding metals of different thickness.
A characteristic feature of our machines, resistance spot welding is a wide possibility to adjust the magnitude of welding current: connect machines to the voltage as 380 V and 220 V, as well as simple and logical current regulation on the control panel, allows you to vary the modes, choosing in each case the optimum welding current.
Simple and intuitive adjustment of the solution electrodes, the free motion of the electrodes, the compression efforts, make it easy to reconfigure the machine resistance spot welding for solving specific production problems.
Thus, customers who wish to buy cars contact spot welding, can save a lot of money, fully using the potential of our machines.
